Linux version 2.6.22-3-k7 (Debian 2.6.22-5) (maks@debian.org) (gcc version 4.1.3 20071019 (prerelease) (Debian 4.1.2-17)) #1 SMP Mon Oct 22 22:51:54 UTC 2007 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000ce000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003beb0000 (usable) BIOS-e820: 000000003beb0000 - 000000003beb8000 (ACPI data) BIOS-e820: 000000003beb8000 - 000000003bf00000 (ACPI NVS) BIOS-e820: 000000003bf00000 - 0000000040000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) 62MB HIGHMEM available. 896MB LOWMEM available. found SMP MP-table at 000f8220 Entering add_active_range(0, 0, 245424) 0 entries of 256 used Zone PFN ranges: DMA 0 -> 4096 Normal 4096 -> 229376 HighMem 229376 -> 245424 early_node_map[1] active PFN ranges 0: 0 -> 245424 On node 0 totalpages: 245424 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 1760 pages used for memmap Normal zone: 223520 pages, LIFO batch:31 HighMem zone: 125 pages used for memmap HighMem zone: 15923 pages, LIFO batch:3 DMI present. ACPI: RSDP 000F8190, 0014 (r0 GATEWA) ACPI: RSDT 3BEB380A, 0034 (r1 GATEWA M300 20060124 LTP 0) ACPI: FACP 3BEB7E20, 0074 (r1 GATEWA M300 20060124 PTL 5F) ACPI: DSDT 3BEB383E, 45E2 (r1 GATEWA M300 20060124 MSFT 100000E) ACPI: FACS 3BEB8FC0, 0040 ACPI: SSDT 3BEB7E94, 00D6 (r1 PTLTD POWERNOW 20060124 LTP 1) ACPI: APIC 3BEB7F6A, 005A (r1 GATEWA M300 20060124 LTP 0) ACPI: MCFG 3BEB7FC4, 003C (r1 GATEWA M300 20060124 LTP 0) ATI board detected. Disabling timer routing over 8254. ACPI: PM-Timer IO Port: 0x8008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 15:4 APIC version 16 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 1, version 33, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000) Built 1 zonelists. Total pages: 243507 Kernel command line: root=/dev/hda5 ro quiet vga=791 mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 16384 bytes) Detected 1790.935 MHz processor. Console: colour dummy device 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 963300k/981696k available (1701k kernel code, 17724k reserved, 660k data, 244k init, 64192k highmem) virtual kernel memory layout: fixmap : 0xfff4e000 - 0xfffff000 ( 708 kB) pkmap : 0xff800000 - 0xffc00000 (4096 kB) vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) .init : 0xc0355000 - 0xc0392000 ( 244 kB) .data : 0xc02a95e7 - 0xc034e784 ( 660 kB) .text : 0xc0100000 - 0xc02a95e7 (1701 kB) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 3585.51 BogoMIPS (lpj=7171022) Security Framework v1.0.0 initialized SELinux: Disabled at boot. Capability LSM initialized Mount-cache hash table entries: 512 CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000001 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU: After all inits, caps: 078bfbff e3d3fbff 00000000 00000410 00000001 00000000 00000001 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Compat vDSO mapped to ffffe000. Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code Freeing SMP alternatives: 11k freed ACPI: Core revision 20070126 CPU0: AMD Turion(tm) 64 Mobile Technology ML-34 stepping 02 Total of 1 processors activated (3585.51 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 ..MP-BIOS bug: 8254 timer not connected to IO-APIC ...trying to set up timer (IRQ0) through the 8259A ... failed. ...trying to set up timer as Virtual Wire IRQ... works. Brought up 1 CPUs Booting paravirtualized kernel on bare hardware NET: Registered protocol family 16 ACPI: bus type pci registered PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved PCI: Not using MMCONFIG. PCI: PCI BIOS revision 2.10 entry at 0xfd89d, last bus=5 PCI: Using configuration type 1 Setting up standard PCI resources ACPI: Interpreter enabled ACPI: (supports S0 S3 S4 S5) ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI: Transparent bridge - 0000:00:14.4 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB6_._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKB] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKC] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKD] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKE] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKU] (IRQs 3 4 5 7) *0, disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 10 devices ACPI: ACPI bus type pnp unregistered PnPBIOS: Disabled by ACPI PNP PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report NET: Registered protocol family 8 NET: Registered protocol family 20 ACPI: RTC can wake from S4 pnp: 00:01: iomem range 0xe0000000-0xefffffff has been reserved pnp: 00:01: iomem range 0xfec00000-0xfec00fff could not be reserved pnp: 00:01: iomem range 0xfee00000-0xfee00fff could not be reserved pnp: 00:06: iomem range 0xe0000-0xfffff could not be reserved pnp: 00:06: iomem range 0xfff80000-0xffffffff could not be reserved pnp: 00:06: iomem range 0x0-0xfff could not be reserved pnp: 00:09: ioport range 0x1080-0x1080 has been reserved pnp: 00:09: ioport range 0x220-0x22f has been reserved pnp: 00:09: ioport range 0x40b-0x40b has been reserved pnp: 00:09: ioport range 0x4d0-0x4d1 has been reserved Time: tsc clocksource has been installed. PCI: Bridge: 0000:00:01.0 IO window: 9000-9fff MEM window: d0100000-d01fffff PREFETCH window: d4000000-d7ffffff PCI: Bridge: 0000:00:06.0 IO window: a000-afff MEM window: d0200000-d02fffff PREFETCH window: disabled. PCI: Bus 6, cardbus bridge: 0000:05:09.0 IO window: 00002000-000020ff IO window: 00002400-000024ff PREFETCH window: 50000000-53ffffff MEM window: 54000000-57ffffff PCI: Bridge: 0000:00:14.4 IO window: 2000-2fff MEM window: d0300000-d03fffff PREFETCH window: 50000000-53ffffff PCI: Setting latency timer of device 0000:00:06.0 to 64 ACPI: PCI Interrupt 0000:05:09.0[A] -> GSI 23 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:05:09.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1572864 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered checking if image is initramfs... it is Switched to high resolution mode on CPU 0 Freeing initrd memory: 6227k freed audit: initializing netlink socket (disabled) audit(1194388277.680:1): initialized highmem bounce pool size: 64 pages VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) PCI: MSI quirk detected. MSI deactivated. Boot video device is 0000:01:05.0 PCI: Setting latency timer of device 0000:00:06.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:06.0:pcie00] vesafb: framebuffer at 0xd4000000, mapped to 0xf8880000, using 3072k, total 65536k vesafb: mode is 1024x768x16, linelength=2048, pages=41 vesafb: protected mode interface info at c000:512b vesafb: pmi: set display start = c00c5199, set palette = c00c51d3 vesafb: pmi: ports = 9010 9016 9054 9038 903c 905c 9000 9004 90b0 90b2 90b4 vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 Console: switching to colour frame buffer device 128x48 fb0: VESA VGA frame buffer device isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Using IPI No-Shortcut mode Freeing unused kernel memory: 244k freed input: AT Translated Set 2 keyboard as /class/input/input0 ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) ACPI: Processor [CPU0] (supports 8 throttling states) ACPI: Thermal Zone [THRM] (72 C) usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 17 ohci_hcd 0000:00:13.0: OHCI Host Controller ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1 ohci_hcd 0000:00:13.0: irq 17, io mem 0xd0000000 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 4 ports detected Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 17 ohci_hcd 0000:00:13.1: OHCI Host Controller ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:13.1: irq 17, io mem 0xd0001000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 4 ports detected ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 17 ehci_hcd 0000:00:13.2: EHCI Host Controller ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3 ehci_hcd 0000:00:13.2: irq 17, io mem 0xd0002000 ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 8 ports detected Marking TSC unstable due to: possible TSC halt in C2. Time: acpi_pm clocksource has been installed. ATIIXP: IDE controller at PCI slot 0000:00:14.1 ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 18 ATIIXP: chipset revision 0 ATIIXP: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x8410-0x8417, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0x8418-0x841f, BIOS settings: hdc:DMA, hdd:pio Probing IDE interface ide0... hda: ST9120824A, ATA DISK drive usb 2-1: new low speed USB device using ohci_hcd and address 2 usb 2-1: configuration #1 chosen from 1 choice usbcore: registered new interface driver hiddev input: Microsoft Microsoft Trackball Optical� as /class/input/input1 input: USB HID v1.00 Mouse [Microsoft Microsoft Trackball Optical�] on usb-0000:00:13.1-1 usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver hda: selected mode 0x45 ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: PHILIPS DVD+/-RW SDVD8820, ATAPI CD/DVD-ROM drive hdc: selected mode 0x42 ide1 at 0x170-0x177,0x376 on irq 15 ACPI: PCI Interrupt 0000:05:09.2[C] -> GSI 21 (level, low) -> IRQ 21 firewire_ohci: Added fw-ohci device 0000:05:09.2, OHCI version 1.10 SCSI subsystem initialized libata version 2.21 loaded. hda: max request size: 512KiB hda: 234441648 sectors (120034 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(100) hda: cache flushes supported hda: hda1 hda2 hda3 < hda5 hda6 hda7 > hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 firewire_core: created new fw device fw0 (0 config rom retries) Attempting manual resume swsusp: Basic memory bitmaps created swsusp: Basic memory bitmaps freed SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled SGI XFS Quota Management subsystem XFS mounting filesystem hda5 Ending clean XFS mount for filesystem: hda5 Linux agpgart interface v0.102 (c) Dave Jones pci_hotplug: PCI Hot Plug PCI Core version: 0.5 shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 18 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:03:00.0 to 64 sky2 0000:03:00.0: v1.14 addr 0xd0200000 irq 19 Yukon-FE (0xb7) rev 1 sky2 eth0: addr 00:e0:b8:b6:14:82 piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device Yenta: CardBus bridge found at 0000:05:09.0 [107b:0300] Yenta: Enabling burst memory read transactions Yenta: Using CSCINT to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:05:09.0, mfunc 0x01ac1b22, devctl 0x64 sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman udev: renamed network interface eth0 to eth1 Yenta: ISA IRQ mask 0x0ef8, PCI irq 16 Socket status: 30000006 Yenta: Raising subordinate bus# of parent bus (#05) from #06 to #09 pcmcia: parent PCI bridge I/O window: 0x2000 - 0x2fff cs: IO port probe 0x2000-0x2fff: clean. pcmcia: parent PCI bridge Memory window: 0xd0300000 - 0xd03fffff pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x53ffffff sdhci: SDHCI controller found at 0000:05:09.4 [104c:8034] (rev 0) ACPI: PCI Interrupt 0000:05:09.4[A] -> GSI 23 (level, low) -> IRQ 16 mmc0: SDHCI at 0xd0309000 irq 16 DMA mmc1: SDHCI at 0xd0308c00 irq 16 DMA mmc2: SDHCI at 0xd0308800 irq 16 DMA ACPI: PCI Interrupt 0000:05:09.3[A] -> GSI 23 (level, low) -> IRQ 16 Real Time Clock Driver v1.12ac input: PC Speaker as /class/input/input2 ACPI: PCI Interrupt 0000:00:14.5[B] -> GSI 17 (level, low) -> IRQ 20 cs: IO port probe 0x100-0x3af: clean. cs: IO port probe 0x3e0-0x4ff: clean. cs: IO port probe 0x820-0x8ff: excluding 0x878-0x87f cs: IO port probe 0xc00-0xcf7: excluding 0xc00-0xc07 0xc10-0xc17 0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcdf cs: IO port probe 0xa00-0xaff: clean. Synaptics Touchpad, model: 1, fw: 5.9, id: 0x23aeb3, caps: 0xa04713/0x10008 input: SynPS/2 Synaptics TouchPad as /class/input/input3 Adding 2048276k swap on /dev/hda2. Priority:-1 extents:1 across:2048276k loop: module loaded ndiswrapper version 1.49rc4 loaded (smp=yes, preempt=no) ndiswrapper: driver bcmwl5 (Broadcom,12/22/2004, 3.100.46.0) loaded ACPI: PCI Interrupt 0000:05:02.0[A] -> GSI 22 (level, low) -> IRQ 22 ndiswrapper: using IRQ 22 wlan0: ethernet device 00:14:a5:c1:ce:38 using NDIS driver: bcmwl5, version: 0x3642e00, NDIS version: 0x501, vendor: 'NDIS Network Adapter', 14E4:4318.5.conf wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK usbcore: registered new interface driver ndiswrapper ndiswrapper: changing interface name from 'wlan0' to 'eth0' udev: renamed network interface wlan0 to eth0 device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com kjournald starting. Commit interval 5 seconds EXT3 FS on hda1, internal journal EXT3-fs: mounted filesystem with ordered data mode. XFS mounting filesystem hda6 Ending clean XFS mount for filesystem: hda6 pcmcia: Detected deprecated PCMCIA ioctl usage from process: discover. pcmcia: This interface will soon be removed from the kernel; please expect breakage unless you upgrade to new tools. pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details. sky2 eth1: enabling interface sky2 eth1: ram buffer 4K sky2 eth1: Link is up at 100 Mbps, full duplex, flow control both powernow-k8: Found 1 AMD Turion(tm) 64 Mobile Technology ML-34 processors (version 2.00.00) powernow-k8: 0 : fid 0xa (1800 MHz), vid 0x4 powernow-k8: 1 : fid 0x8 (1600 MHz), vid 0x6 powernow-k8: 2 : fid 0x0 (800 MHz), vid 0x16 ACPI: Battery Slot [BAT1] (battery present) ACPI: AC Adapter [ACAD] (on-line) input: Power Button (FF) as /class/input/input4 ACPI: Power Button (FF) [PWRF] input: Power Button (CM) as /class/input/input5 ACPI: Power Button (CM) [PWRB] input: Sleep Button (CM) as /class/input/input6 ACPI: Sleep Button (CM) [SLPB] input: Lid Switch as /class/input/input7 ACPI: Lid Switch [LID] lp: driver loaded but no devices found ppdev: user-space parallel port driver Clocksource tsc unstable (delta = -277788759 ns) Bluetooth: Core ver 2.11 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP ver 2.8 Bluetooth: L2CAP socket layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM ver 1.8 [drm] Initialized drm 1.1.0 20060810 ACPI: PCI Interrupt 0000:01:05.0[A] -> GSI 17 (level, low) -> IRQ 20 [drm] Initialized radeon 1.27.0 20060524 on minor 0 [drm] Setting GART location based on new memory map [drm] Loading R300 Microcode [drm] writeback test succeeded in 1 usecs NET: Registered protocol family 10 lo: Disabled Privacy Extensions ADDRCONF(NETDEV_UP): eth0: link is not ready NET: Registered protocol family 4 NET: Registered protocol family 3 NET: Registered protocol family 5 eth1: no IPv6 routers present